RetroScaler2x A/V to HDMI-compatible Converter and Line-doubler for Retro Game Consoles Attention: The RetroScaler2Xdo not supportallPAL-Mconsoles in Brazil. Supported Console but not limited to: Vic20 Atari2600 Msx NES N64 NGC SFC SNES SuperFamicom PIAYSATION2 SEGA Saturn MD2 MD1 Dreamcast Commodore64(C64) Product Features: Signals / Resolutions: The RetroScaler2x can accept240p/480i/288p/576iNTSC/PAL sources to converter to 480p/576p HDMI output (480p for NTSC, 576p for PAL). For example 240p signalsaresupported properly, allowing for a completely progreive linedouble to 480p.480i signals are deinterlaced and doubled also to 480p.Keep in mind that the output resolution of this device only up to480p/576p. Zero Lag: The RetroScaler2x is azerolag device, proven using multiple measurements and different devices. Region Compatibility: Both NTSC and PAL signals are supported, butthey are not convertedto each other. That means you can plug in whatever signal yourtargetdevice is compatible with, but NTSC might not work on PAL HDMI devices and vice versa. Filter Modes: The FIL mode is completely preference-based, but the average retro-gamer prefers the FIL mode off for 2D games (SNES, Genesis, etc) and on for 3D games (N64, Saturn, etc). Also, the FIL mode might help reduce flicker with some 480i-only games. Compatibility: Another great feature of the RetroScaler2x is that it outputs a true 480p60 signal, making it compatible with every device I tested it with! Compatibility is a big iue for retro-gamers, as modern displays arent used to the resolution or refresh rate of these older consoles. This device is an excellent help for streamers who want the highest chance of compatibility. Performance Audio: Audio performance on the RetroScaler2X isgood although we would have to stop short of saying it was perfect. In general uses there are no iues with the audio digitization but on braieresounds like explosions the output may sound a little rougher than it did through the OSSC. This isnt something youre likely to even notice on a TVs speakers, though you might if you have an external amp or home theatre system. In that case of course, its usually perfectly easy to route audio around the RetroScaler2X anyway. The Pa-through: By putting the RetroScaler2X into pa-throughmode, incoming composite, s-video or component signals are simply transparentand digitized into HDMI. Support for 240p is rare in the world of HDMI, but by adding a simple HDMI to VGA converter, you can convert the signal back to the analogue domain again. This makes the unit a perfect transcoder to go with 15 kHz displays like PVMs, or of course, the OSSC. Connecting your RetroScaler2x: 1)Connect a suitable source to the composite,component (YPBPR)or S-video connectors. (The inputs can only be used one at a time and itsstrongly suggested that you do not leave consoles plugged in at the same time, even if they are off) 2)Ensureyou are connected to the USB power,and then switchon your RetroScaler2X. 3)Connect to the display via HDMI interface,and thenplay your games. 4)Select the appropriate video mode through buttonaccording to your needs. Important safety information: Please observe the following safety precautions when using your Retro Scaler2x. Use the correct power supply-- the Retroscaler2x is powered by a regular 5 volt Micro USB port that can be powered by a normal power supply or powered by a device that has a USB port. Please make sure that the power supply you are using meets any of the above requirements. Never use a power supply that is not regulated to prevent damage to the equipment. Turn off the power before connecting/disconnecting the device-- to prevent damage to the device ICs, always turn off the power before connecting the monitor or device. Do not expose to moisture Droplets of moisture-- may contact the PCB and cause a short circuit. Never submerge the unit in water. Keep away from fire or high heat sources RetroScaler2X is not flammable but high temperatures, such as those from a fire or electric heater may melt the plastic casing. Please supervise children-- Retro is not a toy and is not designed for use by children. Please supervise children if they use the Retro. Buttons, connectors and external controls: Component video input--Connect component video (YPBPR) or RGB with sync on green sources to this input. As a note, the chip used in this device does not support RGB, so an RGB SCART input will never be an option. S-video input-- Connect an S-video (4 pins connector) source to this input, other sources are not support. AV input-- Standardcomposite (RCA) connector. Youcan connect sources such as the Nintendo Super Famicom, Nintendo GameCube, N64 etc. HDMI video out--All the received video and audio signals will be output on the modern