This is a nylon brush broom with 52cc Motor. Its nylon brush is good for cleaning up light debris from hard surfaces. It is very suitable for cleaning artificial grass sites, caretakers, street cleaning, and farms. The handheld broom has a two-stroke, 1700W high power engine, which makes cleaning easy with high efficiency. Key Features 🔹High Efficiency: The broom can be used on any surface that is flat. Then, the gasoline broom works with strong power. Thanks to the strong bristle quality, dust, leaves, and snow will be completely removed in the first gear. 🔹Wide Application: It has sturdy replaceable nylon brushes that are strong and easy to grip. 🔹Easy to Use: This sweeping brush is equipped with a comfortable strap that hangs from the body. It is able to adjust the length to suit different angles of work. So it is perfect for long working hours. 🔹Large Cleaning Area: It has a large sweeping head of 60cm, which can sweep a much larger area than ordinary sweeping tools. This makes it very efficient. 🔹Long Endurance Time: Its fuel tank is capable of holding 1L of gasoline, which is a huge capacity. This gives the broom a very long endurance time so it can be used for a long time without refueling. Details ✔Curved Handle: The gas broom has an ergonomically curved handle on the operating lever so that your hands can operate the broom better. This professional design can well reduce the difficulty of the cleaning task. ✔Curved Baffle Design: Behind the brush head there is a large curved baffle. This large curved baffle can block the garbage gathered by the broom while working to ensure the completion of the cleaning. Application It is very suitable for cleaning artificial grass sites, caretakers, street cleaning, and farms. Specification 2 Cycle Oil /Gasoline Mixing Ratio: 1:25 Displacement: 52 cc Net Weight: About 10 kg (22.04 lbs) Brush Head Width: 58cm（22.83 In） Baffle Width: 60cm（23.62 In） Brush Head Diameter: 25.5cm（10.04In） Overall Length: 189cm /74.41inch Engine: 1-Cylinder, 2-Stroke Power: 1.7kw / 2.3hp Cooling: Air-Cooled Fuel Tank Volume: 1L Package Included 1*Host 1*Brush Head 1*Drive Shaft 1*Bezel 1*Handle 1*Proportioning Pot 1*Manual 1*Tool Bag Initiation Step 1.Press the pump oil bubble and suck the fuel into the carburetor. 2.Turn on the ignition switch to the On position. 3.Tighten the fuel tank cover. 4.Close the choke valve. (Note: It is not necessary to close the valve when starting the hot engine.) 5.Pull the rope starter. (Note: After pulling 3-5 times, it can be started. If there is a reaction to start but it fails to start, please open the valve and quickly pull the start handle again.). 6.After the engine starts, open the choke valve. (Note: Keep the choke valve open in the working condition. Notes 1.Before use, please carefully install according to the instructions. During installation, the inner shaft should be parallel to the outer aluminum tube (the visual difference is 0.5-1cm parallel with the aluminum tube), and the inner shaft should be about 0.5cm long to ensure that the aluminum tube is fully installed to the bottom of the gear box; Improper installation of aluminum pipes can lead to problems such as stalling. 2.Please keep the fuel(not included) away from the fire source. 3.The distance between the protective cover and the brush head is recommended to be between 9.84-13.78 inches. 4.The ratio of fuel in use should be proportioned according to the oil level. Fuel should be supplied as needed, please do not use fuel that has been mixed for more than 7 days and non-two-stroke gasoline engine oil. Please empty the fuel tank when not in use for a long period. 5.The damper opens downwards when the engine is running. The warm engine start damper opens downwards, do not close the damper. If the engine is overheated and it is difficult to start, you can increase the accelerator idling speed and start again, or wait for the engine to cool down a little before starting. 6.Please read the instruction manual carefully before use and pay particular attention to the safety instructions contained therein.