Usage Tips:Knee & Shin Guards(If you encounter any problems, please be sure to contact our customer service first. Please do not leave a bad review first. Due to the time difference, etc., the customer service will reply as soon as possible after seeing the message. We very much hope to answer your questions, thank you.)Fitment:For Kawasaki ER-6F 2012-2017For Kawasaki ER-6N 2012-2017For Kawasaki KLE650 2010-2017For Kawasaki 250R(Fi model) 2013-2015For Kawasaki 300 2013-2018For Kawasaki 400R 2013-2016For Kawasaki 400 2018For Kawasaki 650 2012-2016For Kawasaki 1000 2011-2016For Kawasaki 650 2010-2018For Kawasaki 1000 2012-2018For Kawasaki VN900 2011-2015For Kawasaki S 650 2015-2018For Kawasaki 900 2011-2018For Kawasaki W800 2011-2017For Kawasaki Z300 2015-2016For Kawasaki Z650 2017-2018For Kawasaki Z750 2010-2012For Kawasaki Z750R 2011-2012For Kawasaki Z800 2013-2017For Kawasaki Z800e 2013-2017For Kawasaki Z1000 2010-2016For Kawasaki Z1000SX 2011-2016For Kawasaki ZX-6R 636 2006For Kawasaki ZX10R2009For Kawasaki ZRX1200 2011-2015For Kawasaki Brute Force 750() All YearsFor Kawasaki Mule () All YearsFor Kawasaki Teryx () All YearsCondition:100% Color of Light Source:Red/Blue/green/white/orangeItem Name:Speed Gear Display IndicatorSize:4cm*4cm*4cm/1.57inch*1.57inch*1.57inchFeature:Shows current gear numberIndicates current gear from 1 to max of 6. as well as a neutral indicator.Detects the current gear faster than other gear indicators that use speedometer/tachometer signal.Display can be mounted anywhereForeword:Congratulations on your purchase of a gear position indicator,This product will fit all For Kawasaki fuel injected(EFI)motorcycles which have on board Diagnostic System connector. This connector is referred as For KDS(For Kawasaki Diagnostic System) in the For Kawasaki manuals.Unlike other gear indicators available for your bike,this product connects to the diagnostic connector.It make the installation very sample. The unit reads data directly from the ECU, offering faster and more reliable readings than competing products.The display is auto learning,there are no button and no ;programming wire; Know limitations;Your bike is not equipped with Gear Position Sensor. therefore determining the gear in use is only possible when the engine is running and the clutch is released.Installation:1. Find the 4-pole diagnostic connector (also called as For KDS) under the seat, near the ECU module (Black, Grey, or semi-transparent plug).2. Normally it has a removable semi-transparent cap or ?dummy? plug (without wires) attached to it. The connector may be partially covered by black tape.Note: You may find TWO of this connector on your bike. In this case, try both connectors, but only one of them will supply data to this gear indicator. It will not harm your bike if you connect the gear indicator to the wrong plug first.3. Detach the cover (cap) from the plug and connect the gear indicator plug.4. Route the cable to the mounting location along the frame. Peel the green plastic off from the back of the unit, and mount the display.5. Secure the cable with the cable ties supplied, ensuring that the steering movement is not impaired by the cable.Troubleshooting:You may find TWO semi-transparent connectors on the bike with a removable cap or dummy plug.Try the second one if the unit does not work from the first one.Disconnect the Gear Indicator connector and check whether the pins are broken,bent or pushed out of position.Reconnect the plug,and make sure that all connections are good and the connector is fully seated.If you can not execute the setup procedure,your battery might be old or weak.Charge the battery or connect another battery using a jumper cable.If some gears are not indicated properly when the engine is running and clutch is released,rest the unit and setup again.If the problem persists.your clutch might be slipping.(No reset is generally required. If you need to reset, please consult our customer service. The customer service will reply you as soon as possible after seeing the information.)