Simply connect the motherboard of the UPA programmer directly or using a DB9 male or female extension cable (1: 1) Insert the correct configuration key into the slot on the main board and start programming via ZIF or DIP female ! You can also use the included DIL to 10 flat ribbon pins, place it inside the ZIF plug and connect a clip or clamps for the use of ISP from there. MCU. Choose the adapter you want to use, connect the flat cable for the adapter (PIN1 is always indicated on both the cable and the adapter) and also on the 10-pin ISP connector on the main board.Select the VCC supply source via the bridge on the main board next to the ISP connector (on = target upa supply ... off = target has its own supply). Slide the adapter over the soldered PLCC MCU on the target PCB. (No welding, no pinout revision, no pin counting, saves a lot of time and problems and allows your work to be faster, more accurate and easier). Once your workshop is equipped with our set of adapters, you will have a new UPA experience.STMicroelectronics :ST62-40 or 45 or 49 NSCCR16-HCS5(9) or MCS5(9) or MES5(9) or MFS5(9) or MCT5(9) or HCT5(9)for : PIC12F-508 or 509 or 629 or 675,PIC16F-627(A) or 628(A) or 648A or 72 or 73 or 74 or 76 or 77 or 818 or 819 or 83 or 84(A) or 870 or 871 or 872 or 873(A) or 874(A) or 876(A) or 877(A)for :MC68HC05-B6 or B8 or B16 or B16 or B32 or E6 or E6 or H12 or L28 or P3 or P3x or X16 or X32MC68HC08AS20, MC68HC08AS32, MC68HC08AS60, MC68HC08AZ32, MC68HC(9)08AZ32A, MC68HC908AZ60, MC68HC908AZ60A, MC68HC11 or A1 or A8 or E9 or EA9, MC68HC11-E20 or F1 or K4 or KA2 or KA4 or KG4 or KS2 or KS8 or L6 or P2 or PA8 or PH8MC68HC912-B32 or BE32 or D60 or D60A or DC128A or DG128 or DG128A, MC9S12-D64 or A128 or DG128 or DG256 or H128 or H256Atmel 8051 Architecture: AT89S-51 or 52 or 53 or 8252 or 8253Atmel AVR 8-Bit Risk: AT90S-1200 or 2313 or 232 or 2333 or 2343 or 4433 or 4434 or 8515 or 8535, ATmega-8 or 16 or 161 or 162 or 163 or 323 or 64 or 103 or 128, ATtiny-12 or 15 or 2313EEPROMs: 24C-01 or 02 or 04 or 08 or 16 or 32 or 64 or 65 or 128 or 256 or 512, 85C-72 or 82 or 92, BAW574252, -003 or 004 or 005, KKZ-06F, MCM2814, PCA8581, PCF85-81 or 82 or 94 or 98 or 102 or 116, SDA25-16 or 26 or 46, X24C-00 or 01,7002, 93C-06 or 14 or 46 or 56 or 57 or 66 or 76 or 86, 93S-46 or 56 or 66, GRN-001, GRO-002, KKZ-01, S220, S2914, ST61907, XLS93C46EEPROMs:M35080, 25C-010 or 020 or 040 or 080 or 128 or 160 or 256 or 320 or 640, M25P-05 or 10 or 20 or 40 or 80, ST950-10 or 20 or 40 or 80, ST95-160 or 320 or 640, ST95P-02 or 04 or 08, X50-43 or 45CXK-1011 or 1012 or 1013, M6M800-11 or 21 or 41, SDE2506, TC89-101 or 102xEEPROM Only ..uDP780-828A or 948 or 949 or 973 or 974TMS...TMS370CX-02 or 32 or 36 or 42 or 56,78K0 or HC912TMS370CX58 78K0 or HC912 TMS375C006colour: red and green and blueMaterial: plastic andmetalPackage Contents:1x UPA programmer1x USB cable1 x Mainboard with 40pin DIL ZIF (600mil) socket and 14pin SOIC ZIF (150mil) socketOnly the above package content, other products are not included.Note: Light and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is 1-3cm.